Thermaltake W0013 480W Silent PurePower ATX 2.03 Power Supply for AMD K7 and Intel ATX +12V 1.1 SATA: W0013RU (Retail) (Discontinued)

• Designed for AMD K7 and Intel ATX +12V 1.1 and ATX 2.03 version
(Fully Support Pentium 4)
• Serial ATA (Advanced Technology Attachment)
• Peak Output : 550W
• 2 adjustable manual fan speed control in the front and rear side of the case. (from 1300 rpm at 25°C~ 4800 rpm at 90°C).
• Temperature Automatic Fan Speed Control
• Noise : 17 dBA at 1300 rpm, 45 dB at 4800 rpm
• Dual fans power supply
• Xaser badge on side panel
• Black / Silver color printing

Silent Purepower 480W power supply unit is also equipped with advanced Temperature Control Technology. This enables the power supply unit to operate at its maximum capability while keeping the noise level down to an impressive 17dBA during normal operation.

Additionally, Manual Fan Speed Control gives the user ability to take control of Silent Purepower (It still works without connecting fan speed controller). Following RPM v. Temperature graph illustrates the RPM curve in corresponding to unit enclosure temperature. Red curve (Graph 1) indicates the speed that the fan operates at during Automatic Temperature Control. To ensure proper cooling, Silent Purepower 480W regulates the range of fan speed that user can manually adjust. i.e. at 40?C, user can manually adjust the speed within the range of 1125 RPM to 3125 RPM.

Serial ATA In recent years, two alternative serial interface technologies - Universal Serial Bus (USB) and IEEE 1394 - have been proposed as possible replacements for the Parallel ATA interface. However, neither interface has been able to offer the combination of low cost and high performance that has been the key to success of the traditional Parallel ATA interface. However, in spite of its success, the Parallel ATA interface has a long history of design issues. Most of these issues have been successfully overcome or worked around. However, some have persisted, and in 1999 the Serial ATA Working Group - comprising companies including APT Technologies, Dell, IBM, Intel, Maxtor, Quantum, and Seagate Technologies - was formed to begin work on a Serial Advanced Technology Attachment (ATA) storage interface for hard-disk drives and ATA Packet Interface (ATAPI) devices that is expected to replace the current Parallel ATA interface.

Compared with Parallel ATA, Serial ATA will have lower signalling voltages and reduced pin count, will be faster and more robust, and will have a much smaller cable. It will also be completely software compatible with Parallel ATA and provide backward compatibility for legacy Parallel ATA and ATAPI devices. This will be achieved either using chip sets that support Parallel ATA devices in conjunction with discrete components that support Serial ATA devices, or by the use of serial and parallel dongles, which adapt parallel devices to a serial controller or adapt serial devices to a parallel controller.
Serial ATA's primary benefits over Parallel ATA include:

• Reductions in voltage and pin count: Serial ATA's low-voltage requirement (500 mV peak-to-peak) will effectively alleviate the increasingly difficult-to-accommodate 5-volt signaling requirement that hampers the current Parallel ATA interface.
• Smaller, easier-to-route cables: Elimination of the cable-length limitation: The Serial ATA architecture replaces the wide Parallel ATA ribbon cable with a thin, flexible cable that can be up to 1 meter in length. The serial cable is smaller and easier to route inside a PC's chassis and eliminates the need for the large and cumbersome 40-pin connectors required by Parallel ATA. The small-diameter cable also helps improve air flow inside the PC system chassis and will facilitate future designs of smaller PC systems.
• Improved data robustness: Serial ATA will offer more thorough error checking and error correcting capabilities than are currently available with Parallel ATA. The end-to-end integrity of transferred commands and data can be guaranteed across the serial bus.
  First-generation Serial ATA is expected to ship in 2001 with support for data transfer rates of up to 150 MBps. Subsequent versions of the specification are expected to increase performance to support data transfer rates of 300 MBps and, later, 600 MBps.

+5V

-5V

Max. Load

40A

0.3A

18A

0.8A

30A

2.0A

Min. Load

1.5A

0A

0.2A

0A

0.3A

0A

Load Reg.

+5% ~ -5%

+10% ~ -10%

+5% ~ -5%

+10% ~ -10%

+5% ~ -5%

+5% ~ -5%

Ripple
V(p-p)

50mV

100mV

120mV

120mV

50mV

50mV

HDMI Cables and Switches
Apogee HDMI 1.3b Cables and Switchers

Core 2 Quad
Intel Quad-Core E8400; Dual- Core E7500

Hard Drive Docking Station
USB 2.0, SATA, Thermaltake, Vantec

Best Sellers